| help |
Lists all the registered commands |
| g-ts |
Get FreeRTOS tasks |
| g-hs |
Get heap stats |
| e-r |
Reset RfmUsb |
| g-fv |
Get firmware version |
| g-ob |
Get output base |
| s-ob |
Set output base: 0-1 |
| s-co |
Set cli output: 0-1 |
| g-msn |
Get mcu serial number |
| g-rv |
Get register value. 0-0xFF |
| s-rv |
Set register value. 0-0xFF 0-0xFF |
| e-tx |
Execute tx: hex(1-66) [tx count: 1 - 20] [tx interval: 10 - 1000] [timeout: 10 - 5000] |
| e-bl |
Enter bootloader |
| g-lrssi |
Get last packet rssi |
| g-fifo |
Read the fifo |
| s-fifo |
Write the fifo: hex (1-66) |
| g-dim |
Get dio interrupt mask |
| s-dim |
Set dio interrupt mask: 0-0x3F |
| g-dio |
Get dio mapping: 0-5 |
| s-dio |
Set dio mapping: 0-5 0-3 |
| g-so |
Get sequencer off |
| s-so |
Set sequencer off: 0-1 |
| g-lo |
Get listen on |
| s-lo |
Set listen on: 0-1 |
| e-lma |
Execute listen mode abort. Mode: 0-5 |
| g-om |
Get operating mode |
| s-om |
Set operating mode: 0-5 |
| g-dm |
Get data mode |
| s-dm |
Set data mode: 0-3 |
| g-mt |
Get modulation type |
| s-mt |
Set modulation type: 0-1 |
| g-fs |
Get fsk shaping |
| s-fs |
Set fsk shaping: 0-4 |
| g-os |
Get ook shaping |
| s-os |
Set ook shaping: 0-2 |
| g-br |
Get bit rate |
| s-br |
Set bit rate: 1200-300000 |
| g-fd |
Get freq deviation |
| s-fd |
Set freq deviation: 0-0x3FFF |
| g-f |
Get frequency |
| s-f |
Set frequency: 0-102E+7 |
| e-rc |
Calibrate rc oscillator |
| g-ab |
Get afc beta |
| s-ab |
Set afc beta: 0-1 |
| g-ir |
Get idle resolution |
| s-ir |
Set idle resolution: 0-3 |
| g-rr |
Get rx resolution |
| s-rr |
Set rx resolution: 0-3 |
| g-lc |
Get listen criteria |
| s-lc |
Set listen criteria: 0-1 |
| g-lem |
Get listen end mode |
| s-lem |
Set listen end mode: 0-2 |
| g-lic |
Get listen idle coefficient |
| s-lic |
Set listen idle coefficient: 0-255 |
| g-lrc |
Get listen rx coefficient |
| s-lrc |
Set listen rx coefficient: 0-255 |
| g-v |
Get radio version |
| g-op |
Get output power level dBm |
| s-op |
Set output power level dBm: -2 - 20 |
| g-par |
Get power amp ramp times |
| s-par |
Set power amp ramp times: 0-15 |
| g-ocp |
Get ocp |
| s-ocp |
Set ocp: 0-1 |
| g-ocpt |
Get ocp trim |
| s-ocpt |
Set ocp trim: 0-15 |
| g-lnaz |
Get Lna Impedance |
| s-lnaz |
Set lna impedance: 0-1 |
| g-lnag |
Get lna gain |
| g-lnags |
Get lna gain select |
| s-lnags |
Set lna gain select: 0-7 |
| g-df |
Get dcc frequency |
| s-df |
Set dcc frequency: 0-7 |
| g-dfa |
Get dcc freq for afc |
| s-dfa |
Set dcc freq for afc: 0-7 |
| g-ott |
Get ook threshold type |
| s-ott |
Set ook threshold type: 0-3 |
| g-opts |
Get ook peak threshold step |
| s-opts |
Set ook peak threshold step: 0-7 |
| g-optd |
Get ook peak threshold decrement |
| s-optd |
Set ook peak threshold decrement: 0-7 |
| g-oatf |
Get ook average threshold filter |
| s-oatf |
Set ook average threshold filter: 0-3 |
| g-oft |
Get ook fixed threshold |
| s-oft |
Set ook fixed threshold: 0-255 |
| e-fei |
Executes a fei measurement |
| g-aac |
Get afc auto clear |
| s-aac |
Set afc auto clear: 0-1 |
| g-aao |
Get afc auto on |
| s-aao |
Set afc auto on: 0-1 |
| e-ac |
Execute afc clear |
| e-a |
Executes afc |
| e-ac |
Clear afc value |
| g-afc |
Get afc value |
| g-fei |
Get fei value |
| e-rssi |
Execute rssi measurement |
| g-r |
Get rssi value |
| s-rxbw |
Set rx channel filter bandwidth: 0-23 |
| g-rxbw |
Get rx channel filter bandwidth |
| s-rxbwa |
Set rx channel filter bandwidth for afc: 0-23 |
| g-rxbwa |
Get rx channel filter bandwidth for afc |
| g-rt |
Get rssi threshold |
| s-rt |
Set rssi threshold: -115 - 0 |
| g-trs |
Get timeout rx start |
| s-trs |
Set timeout rx start: 0-255 |
| g-trt |
Get timeout rssi threshold |
| s-trt |
Get timeout rssi threshold: 0-255 |
| g-irq |
Get irq flags |
| s-irq |
Set irq flags. 010-0x0910 |
| g-ps |
Get preamble size |
| s-ps |
Set preamble size: 0-65535 |
| g-se |
Get sync enable |
| s-se |
Set sync enable: 0-1 |
| g-ffc |
Get fifo fill condition |
| s-ffc |
Set fifo fill condition: 0-1 |
| g-ss |
Get sync size |
| s-ss |
Set sync size: 0-7 |
| g-sbe |
Get sync bit errors |
| s-sbe |
Set sync bit errors: 0-7 |
| g-sync |
Get sync bytes |
| s-sync |
Set sync bytes: hex (1-8) |
| g-pf |
Get packet format |
| s-pf |
Set packet format: 0-1 |
| g-dfe |
Get dc free encoding |
| s-dfe |
Set dc free encoding: 0-3 |
| g-crc |
Get crc check on |
| s-crc |
Set crc check on: 0-1 |
| g-caco |
Get crc auto clear off |
| s-caco |
Set crc auto clear off: 0-1 |
| g-af |
Get address filter |
| s-af |
Set address filter: 0-3 |
| g-pl |
Get packet length |
| s-pl |
Set packet length: 0-255 |
| g-na |
Get node address |
| s-na |
Set node address: 0-255 |
| g-ba |
Get broadcast address |
| s-ba |
Set broadcast address: 0-255 |
| g-amec |
Get auto mode enter condition |
| s-amec |
Set auto mode enter condition: 0-7 |
| g-amexc |
Get auto mode exit condition |
| s-amexc |
Set auto mode exit condition: 0-7 |
| g-im |
Get intermediate mode |
| s-im |
Set intermediate mode: 0-3 |
| g-tsc |
Get tx start condition |
| s-tsc |
Get tx start condition: 0-1 |
| g-ft |
Get fifo threshold |
| s-ft |
Set fifo threshold: 0-127 |
| g-iprd |
Get inter packet rx delay |
| s-iprd |
Set inter packet rx delay: 0-15 |
| e-rr |
Execute restarts rx |
| g-arre |
Get auto rx restart enable |
| s-arre |
Set auto rx restart enable: 0-1 |
| s-aes |
Set aes key: hex(1-16) |
| g-ae |
Get aes enabled |
| s-ae |
Set aes enabled: 0-1 |
| e-tm |
Execute temperature measurement |
| g-t |
Get temperature value |
| g-sb |
Get sensitivity boost |
| s-sb |
Set sensitivity boost: 0-1 |
| g-cd |
Get continuous dagc |
| s-cd |
Set continuous dagc: 0-2 |
| g-lbao |
Get low beta afc offset |
| s-lbao |
Set low beta afc offset: 0-1 |
| g-be |
Get io buffer read enable |
| s-be |
Set io buffer read enable |
| g-bi |
Get io buffer info |
| r-b |
Read io buffer: [count: 1-256] |
| w-b |
Write io buffer: hex (1-64) |
| e-btx |
Execute io buffer transmit |